Lubricant
Ionization Smoke Alarm
View:
Active Filters :
Part #:KIDI9050
- The Kidde i9050 is a full size, ionization, battery operated smoke alarm designed to protect you and your family from the dangers of smoke and fire. The i9050 is powered by a 9V battery, providing continuous protection even during power outages. This unit includes a flashing red LED to indicate the alarm is receiving power. The i9050 is UL Listed and includes a 10 year limited warranty.
Benefits
The Kidde i9050 basic, battery operated smoke alarm provides you and your family an early warning signal against the dangers of fire and smoke. This easy to install smoke alarm includes a test button to verify the unit&rsquos electronic circuitry, horn and battery function are work properly. The i9050 also includes a tamper resist feature to help deter theft or tampering. This smoke alarm is powered by a 9V battery and is suitable for all living areas. This alarm uses ionization sensing technology. Ionization sensing alarms may detect invisible fire particles (associated with flaming fires) sooner than photoelectric alarms. Photoelectric sensing alarms may detect visible particles (associated with smoldering fires) sooner than ionization alarms. Kidde strongly recommends that both ionization and photoelectric smoke alarms be installed to help insure maximum detection of the various types of fire that can occur within the home.
Easy Installation &ndash No wiring required.
Battery Operated (9V battery included) &ndash Provides continuous protection even during power failures.
Quality Design &ndash 10 year limited warranty.
Flashing LED &ndash Indicates alarm is receiving power.
Test Button &ndash Verifies battery and alarm operation.
Low Battery Indicator &ndash Chirps when battery needs replacement.
Technical Specifications
Model
i9050
Power Source
9V Battery (included)
Audio Alarm
85dB at 10ft
Temperature Range
40F to 100F (4C to 38C)
Humidity Range
up to 85% relative humidity (RH)
Sensor
Ionization
Size
5&rdquo in diameter x 1.75&rdquo depth
Weight
.62lbs
Interconnects
No
LED
Red, normal operation
Warranty
10 year limited warranty
$
9.22
PK
Qty:
Part #:SMI100
- SMOKE ALARM TYPE DUAL IONIZATION OPERATION TYPE UL 217 APPROVAL 85 DB AT 10 FT HORN TYPE 9 V BATTERY VOLTAGE RATING/SOURCE RED LED INDICATING DC POWER LED/STROBE TYPE BRK[R] BRAND SIZE 4.25 INCH DIA X 1.6 INCH H CARBON ZINC BATTERY FG250 MODEL
$
13.86
Qty:
$
46.59
Qty:
Part #:SMI100-AC
- 120V AC/DC Smoke Alarm The 9120 Series smoke alarms have been designed to install faster, perform better and be even smarter than before. These improvements help reduce nuisance alarms and save you time and money.
» Single button test/silence » 9V Battery Backup » Latching alarm indicator - remembers which unit initiated an alarm » Smart Technology - helps reduce the number of nuisance alarms » Perfect Mount - allows for easy alignment of alarm » Dust Cover » Easy Installation/Maintenance - Preferred features include a large opening in the mounting bracket for easy access to wiring. Keyhole slots in the mounting bracket eliminate the need to remove the electrical box screws for installation. A battery pull tab keeps the battery fresh until the home is occupied. Battery installation and removal can occur while the unit is mounted to the ceiling or wall via the side load battery compartment. Two locking features are provided to prevent battery theft and/or theft of the unit. Connection to AC power is made with a "Quick-Connect" wiring harness. Installation is quick, easy and cost effective. » 10-Year Limited Warranty
$
14.91
Qty:
Part #:KIDI12010S
- The Kidde i12010S is an AC/DC powered, ionization smoke alarm that operates on a 120V power source with sealed-in lithium battery backup. This alarm uses ionization sensing technology. Ionization sensing alarms may detect invisible fire particles (associated with flaming fires) sooner than photoelectric alarms. Photoelectric sensing alarms may detect visible particles (associated with smoldering fires) sooner than ionization alarms. Leading authorities recommend that both ionization and photoelectric smoke alarms be installed to help insure maximum detection of the various types of fires that can occur within the home.
The i12010S contains a 10-year tamper proof battery that eliminates the need for battery replacement, and ends worry over unauthorized battery removal. The alarm provides continuous protection from smoke and fire, even during power outages. At the end of alarm life, the unit will chirp, indicating the alarm is in need of replacement. The customer can use a simple tool such as a screwdriver to deactivate the unit, stopping the chirp and making it safe for disposal. The end of life signal can be temporarily silenced to allow for replacement at a more convenient time.
Easy Installation
Battery backup automatically activates when the alarm is attached to mounting bracket.
Large mounting base makes mounting easier, protects surface paint from dirt and covers imperfections.
Pre-stripped wiring harness with easy off cap does not require stripper tool. Tinned strands increase conductivity and wire nut grip.
Fewer Callbacks
10-year sealed battery substitutes need for routine 9V replacement.
Large centrally located Test/Hush® alarm control button silences nuisance alarms for approximately 9 minutes.
Dust cover protects sensor from contaminates during construction, reducing nuisance alarms.
User-Friendly Features
Red LED indicates alarm mode, Green LED indicates AC power is present.
Interconnectable with up to 24 devices (of which 18 can be initiating) including smoke, CO and heat alarms. See user guide for complete instructions.
End of Life Hush feature allows user to temporarily silence end of life chirp 3 days at a time for a maximum of 30 day life extension.
Technical Specifications
Model
i12010S
Power Source
120VAC (60 Hz, 45mA Max)
Sensor
Ionization
Audio Alarm
85dB at 10ft
Temperature Range
40F (4.4C) to 100F (37.8C)
Humidity Range
Up to 95% relative humidity (RH), non-condensing
Size
5.5&rdquo in diameter x 1.75&rdquo depth
Weight
.45lbs
Interconnects
Up to 24 Kidde devices
Warranty
10 year limited
$
25.86
Qty:
Part #:900CUAR
- Description
The Kidde KN-COSM-IBA uses breakthrough technology to offer a fast response to real fires, including smoldering and fast-flaming, as well as protect you from carbon monoxide and dramatically reduce the chance of nuisance alarms. The Intelligent sensor technology combines the detection capabilities of an ionization smoke sensor &ndash which is more likely to detect smaller, less visible fire particles, like those produced by flaming fires &ndash with that of an electrochemical sensor, which is used to detect CO. Since carbon monoxide is present in all fires, having both detection chambers work together in one alarm is a breakthrough in the fire safety industry. When either sensor notices a potential hazard, it will communicate with the other. Depending on what is detected, the alarm will adjust its smoke sensitivity in order to better discriminate between a real hazard and a false one. This constant communication enhances the alarm&rsquos overall performance in all fires, and significantly reduces the potential for a nuisance alarm.
Leading authorities recommend that both ionization and photoelectric smoke alarms be installed to help ensure maximum detection of the various types of fires that can occur within the home. Ionization sensing alarms may detect invisible fire particles (associated with fast flaming fires) sooner than photoelectric alarms. Photoelectric sensing alarms may detect visible fire particles (associated with slow smoldering fires) sooner than ionization alarms.
Alarm Warnings
Fire
The red LED will flash and be accompanied by three long alarm beeps followed by a verbal warning message &ldquoFIRE!&rdquo. The alarm pattern will repeat until smoke is eliminated.
Carbon Monoxide
Four short alarm beeps followed by a verbal warning &ldquoWARNING! CARBON MONOXIDE!&rdquo This continues until the unit is reset or the CO is eliminated.
Low Battery
One chirp followed by warning &ldquoLOW BATTERY.&rdquo The red LED light will flash. This pattern will continue every minute for at least seven days. Under battery power, the &ldquoLOW BATTERY&rdquo voice only occurs once every 15 minutes.
Voice Hush Indication
&ldquoHUSH MODE ACTIVATED&rdquo and &ldquoHUSH MODE CANCELLED&rdquo voice announcement.
Peak Level Memory
If the alarm had detected a CO level of 100ppm or higher when the Test/Reset button is pressed, the unit will announce &ldquoCARBON MONOXIDE PREVIOUSLY DETECTED&rdquo to warn of the CO incident.
Smart Interconnect&trade- Interconnects up to 24 Kidde devices (of which 18 can be initiating).
Battery Backup (2-AA batteries included)- Provides protection during power outages.
Front Loading Battery Door- Replace the backup batteries without disconnecting from mounting bracket
Battery Lockout System- The battery door will not close unless the batteries are properly installed.
Alarm Tamper Resist- Helps deter from tampering and theft.
Adjustable Mounting Bracket- Makes installation fast and easy. Works with existing smoke and combination smoke and CO mounting brackets.
Peak Level Memory- Announces &ldquoCARBON MONOXIDE PREVIOUSLY DETECTED&rdquo if alarm has detected a CO level of 100ppm or higher since it was last reset.
Hush&trade Feature- Silences nuisance alarms for approximately 9 minutes. (Smoke must be present before Hush&trade is activated)
Ionization Sensor Technology- Ideal for detecting fast flaming and other types of fires.
Test Button Functions&ndash Tests the unit for proper operation
Peak Level memory
Resets the Carbon Monoxide alarm
Green LED- Illuminates to indicate the unit is receiving AC power. Flashes once every 60 seconds to indicate battery only mode. Flashes once per second during alarm to indicate initiating alarm. Flashes once every 16 seconds to indicate smoke or CO previously detected. Flashes every 2 seconds while the alarm is in HUSH&trade mode.
Red LED- When a dangerous level of smoke or carbon monoxide is detected the red LED will flash. If the unit malfunctions, the red LED will flash and the unit will chirp every 30 seconds.
Technical Specifications
Model
KN-COSM-IBA
Power Source
120VAC, 60Hz 45mA max per alarm 2 AA battery backup
SmokeSensor
Ionization
CoSensor
Electrochemical
Audio Alarm
85dB at 10ft
Temperature Range
40F (4.4C) to 100F (37.8C)
Humidity Range
10%-95% relative humidity, non-condensing
Size
5.6&rdquo in diameter x 1.8&rdquo depth
Weight
1 lb.
Wiring
Quick connect plug with 6&rdquo pigtails
Interconnects
Up to 24 Kidde devices (of which 18 can be initiating)
Warranty
10 year limited
$
37.34
Qty:
Part #:KLE32303
-
14-in-1 Multi-Bit Adjustable Length Screwdriver
32303
Multi-bit screwdriver includes 13 different screwdriver bits and a 1/4-Inch nut driver
Industrial-strength bits that are conveniently housed in the handle
Adjust the length of the blade for easier access
Impact rated blade can be removed for use as an impact driver attachment
Stainless steel bit holder contains powerful rare earth magnets for securing bits and fasteners
Cushion-Grip handle for maximum comfort
Spin cap for optimum and precise control
Qty:
Part #:KLE32305
-
15-in-1 Multi-Bit Ratcheting Screwdriver
32305
Multi-Bit screwdriver features a durable ratcheting mechanism for faster and easier all-day driving
On-board storage of 14 different double-sided screwdriver bits and a 1/4-Inch nut driver
Industrial-strength bits that are conveniently housed in the handle
Collar sets ratchet direction at forward, fixed and reverse
Cushion-Grip handle for great torque and maximum comfort
Spin cap for optimum and precise control
Includes Phillips (#0, #1, #2, #3), Slotted (3/16-Inch, 1/4-Inch), Square (#1, #2), Torx® (T10, T15, T20, T25), and Combo (#1, #2) bits
TORX® is a registered trademark of Acument Intellectual Properties, LLC
Qty:
Part #:KLE32307
-
27-in-1 Multi-Bit Tamperproof Screwdriver
32307
Multi-Bit screwdriver features convenient on-board storage of 26 different tamperproof bits and a 1/4-Inch nut driver
Barrel contains powerful rare earth magnets for securing bits and fasteners
Industrial-strength, double-sided bits that are conveniently housed in the handle eliminating the need for a bulky bit block
Stainless steel barrel provides great impact and wear resistance
Cushion-Grip handle for maximum comfort
Spin cap for optimum and precise control
Includes the following tamper-proof bits Torx®, TORQ-SET®, Hex, and Spanner
TORQ-SET® is a registered trademark of Phillips Screw Co TORX® is a registered trademark of Acument Intellectual Properties, LLC
Qty:
Part #:KLE32308
-
8-in-1 Multi-Bit Adjustable Length Stubby Screwdriver
32308
Multi-bit stubby screwdriver includes 7 different screwdriver bits and a 1/4-Inch nut driver
Compact driver reaches easily into tight spots
Industrial-strength bits that are conveniently housed in the handle
Adjust the length of the blade for easier access
Impact rated blade can be removed for use as an impact driver attachment
Stainless steel bit holder contains powerful rare earth magnets for securing bits and fasteners
Cushion-Grip handle for maximum comfort
Spin cap for optimum and precise control
Qty:
Part #:KLE32476
- PHILLIPS, SLOTTED TYPE CHROME PLATED FINISH 7-3/4 INCH OVERALL LENGTH 4 INCH SHANK LENGTH HEAT TREATED PROCESS CUSHION GRIP HANDLE, PRECISION, 5-IN-1 STYLE BLACK/YELLOW HANDLE COLOR 3/16 INCH, 9/32 INCH (SLOTTED), #1, #2 (PHILLIPS), 5/16 INCH (NUTDRIVER) TIP SIZE TEMPERED STEEL SHANK MATERIAL TIP-IDENT[R] BRAND APPLICABLE STANDARD ASME/ANSI
Qty:
Qty:
Part #:KLE32500MAG
-
11-in-1 Magnetic Screwdriver / Nut Driver
32500MAG
Integrated screwdriver / nut driver magnetic barrel holds 8 popular tips and converts to 3 nut driver sizes
Strong, rare earth magnets securely hold bits and fasteners
Industrial strength heat treated bits
Interchangeable shaft for quick and easy switch out
Cushion-Grip handle for greater torque and comfort
Includes tips 3/8-Inch, 5/16-Inch and 1/4-Inch nut drivers, #1 and #2 Phillips, 1/4-Inch and 3/16-Inch slotted, T10 and T15 TORX®, and #1 and #2 square recess
Blast-finished bit tips provide a firm hold and reduce cam-out
The following replacement bits are available see Cat. No. 32482 (#1 Phillips and 3/16-Inch Slotted), Cat. No. 32483 (#2 Phillips and 1/4-Inch Slotted), Cat. No. 32484 (#1 Square and #2 Square), and Cat. No. 32485 (T10 TORX and T15 TORX)
Qty:
Qty:
$
15.11
Qty:
Part #:CUTARP00002CHB
- USED ON METER BREAKER USED ON MODEL/BRAND ARP WEIGHT 3 LB ITEM HUB CLOSURE PLATE
$
7.20
Qty:
Part #:CUTARP00003CH1
- METER SOCKET ENTRY TYPE 1 INCH HUB SIZE USED ON METER SOCKET APPROVAL UL ARP MODEL
$
12.80
Qty:
$
11.90
Qty:
$
10.25
Qty:
$
11.90
Qty:
$
16.27
Qty:
$
52.10
Qty:
Qty:
$
12.27
Qty:
Displaying: 1 - 24 of 31 Matching Items